Main lug load center, intended for fixed applications. 70 A, 2 space/4 circuits. Surface mount cover with door and a NEMA type 1 enclosure for indoor use. Single phase unit, features a copper bus for conductivity and is rated for up to 10,000 SCCR. ANSI certified and UL listed.

Main lug load center, indoor, 30 A, 2 space/2 circuits. Accommodates both overhead and underground feed applications. 1 in maximum knockout on the top and bottom of the enclosure. Comes with a doorless surface mount cover and factory installed main lugs. UL listed.

Single phase, 2-pole, 3-wire, 2 blades and fuseholders, factory installed solid neutral, 120/240 VAC. With metallic enclosure for indoor use. Designed to open or close an electrical circuit in general duty applications. Rated 1-1/2 hp. For residential or commercial applications. For PK3GTA-1 field installable service ground bar kit. With plug type fuse protection. Lugs suitable for aluminum or copper conductors. Spring reinforced plated copper fuse clips. ANSI Certified and UL listed.

Main lug indoor load center, 70 A, 2 space/4 circuits. Intended for overhead or underground feed. 1-1/4 in maximum knockouts in the top and bottom end walls. NEMA 3R enclosure for outdoor use with a factory included cover. Copper bus for conductivity. UL listed.

Eaton Load Center, 120/240 V, 100 A, Number of Phases: 1, Number of Spaces: 10, Number of Poles: 20, Number of Circuits: 20, Breaker/Load Center Type: Main Breaker, Plug-On Neutral, Cable Size: #4-1/0 AWG, Bus Bar Material: Aluminum, Bus Bar Rating: 100 A, Enclosure Type: NEMA 3R, Flush, Surface Mounting

Load Centers are enclosures specifically designed to house the branch circuit breakers and wiring required to distribute power to individual circuits. They contain either a main breaker when used at the service entrance point or a main lug when used as a sub-panel to add circuits to existing service. The main breaker protects the main entire panel and can be used as a service disconnect. The branch breakers protect the wires leading to individual electrical loads such as fixtures and outlets.

Siemens Closure Plate, 3/4 in Nominal, Dimensions: 12.8 X 5.2 X 3.7 in

Main lug outdoor load center, 100 A, 8 space/16 circuit, has a 2-1/2 in maximum type B hub in the top end wall, a 1-1/2 in maximum knockout in the bottom end wall and a B-cap covering on the 2 in bushed opening. NEMA type 3R enclosure with a rainproof cover for outdoor use. ANSI certified and UL listed.

Steel enclosure. 3-pole, 4-wire, 3 blades, 3 class H cartridge fuses (not included), solid neutral, 120/240 VAC, Rated 1-1/2 to 3 hp single phase, to 7-1/2 hp 3-phase at 240 V only when dual element fuses are used. For residential or light commercial applications. Suitable for light duty motor circuits and service entrance. For use on systems capable of delivering up to 10,000 rms, symmetrical fault current. Ample wire bending space for easier installation. DS100GK ground lug kit sold separately. 6-3/4 in x 9-1/8 in x 6-3/4 in. UL listed file No.E5239; meets UL98 for enclosed switches and NEMA standard KS1.

Suitable for use as service entrance equipment. Removable closing cap not included. Equipment ground. 14-3 AWG lug wire range. Designed to comply with code requirements for disconnecting central air conditioners and heat pumps. Open sides and top for quick installation. Impact and corrosion-resistant GE Noryl thermoplastic resin. 2-pole, 3-wire, 120/240 VAC, rated 10 hp. 5-3/4 in x 8 in x 3-1/8 in. UL1429 enclosed pullout switch, UL Listed.

Steel enclosure. 2-pole, 3-wire, 120/240 VAC, rated 10 hp. Uses cartridge fuses. For central air conditioner. Designed to comply with code requirements for disconnecting means within sight of central air conditioners and heat pumps. Removable closing cap not included. Equipment ground. 14-3 AWG lug wire range. 6-1/2 x 9 x 3-1/4 in. UL869 service equipment, UL listed.

Steel enclosure. 2-pole, 3-wire, 240 VAC, rated 10 hp. For central air conditioner. Removable closing cap not included. Equipment ground. 14-3 AWG lug wire range. 4-3/4 x 7-1/2 x 2 in. UL1429 enclosure pullout switch, UL listed.

PowerMark Gold load centers lower your costs by making installation faster and easier, increasing application flexibility and reducing inventory requirements. At the same time, they deliver obvious and significant advances in design, function and quality.

PowerMark Gold load centers lower your costs by making installation faster and easier, increasing application flexibility and reducing inventory requirements. At the same time, they deliver obvious and significant advances in design, function and quality.

PowerMark Gold load centers lower your costs by making installation faster and easier, increasing application flexibility and reducing inventory requirements. At the same time, they deliver obvious and significant advances in design, function and quality.

PowerMark Gold load centers lower your costs by making installation faster and easier, increasing application flexibility and reducing inventory requirements. At the same time, they deliver obvious and significant advances in design, function and quality.

PowerMark Gold load centers lower your costs by making installation faster and easier, increasing application flexibility and reducing inventory requirements. At the same time, they deliver obvious and significant advances in design, function and quality.

PowerMark Gold load centers lower your costs by making installation faster and easier, increasing application flexibility and reducing inventory requirements. At the same time, they deliver obvious and significant advances in design, function and quality.

PowerMark Gold load centers lower your costs by making installation faster and easier, increasing application flexibility and reducing inventory requirements. At the same time, they deliver obvious and significant advances in design, function and quality.

PowerMark Gold load centers lower your costs by making installation faster and easier, increasing application flexibility and reducing inventory requirements. At the same time, they deliver obvious and significant advances in design, function and quality.

PowerMark Gold load centers lower your costs by making installation faster and easier, increasing application flexibility and reducing inventory requirements. At the same time, they deliver obvious and significant advances in design, function and quality.

GE load centers lower your costs by making installation faster and easier and by increasing application flexibility. At the same time, they deliver obvious and significant advances in design, function and quality.

Load Centers are enclosures specifically designed to house the branch circuit breakers and wiring required to distribute power to individual circuits. They contain either a main breaker when used at the service entrance point or a main lug when used as a sub-panel to add circuits to existing service. The main breaker protects the main entire panel and can be used as a service disconnect. The branch breakers protect the wires leading to individual electrical loads such as fixtures and outlets.

Load Centers are enclosures specifically designed to house the branch circuit breakers and wiring required to distribute power to individual circuits. They contain either a main breaker when used at the service entrance point or a main lug when used as a sub-panel to add circuits to existing service. The main breaker protects the main entire panel and can be used as a service disconnect. The branch breakers protect the wires leading to individual electrical loads such as fixtures and outlets.

Load Centers are enclosures specifically designed to house the branch circuit breakers and wiring required to distribute power to individual circuits. They contain either a main breaker when used at the service entrance point or a main lug when used as a sub-panel to add circuits to existing service. The main breaker protects the main entire panel and can be used as a service disconnect. The branch breakers protect the wires leading to individual electrical loads such as fixtures and outlets.

Rainproof galvanized steel enclosure. Single phase, 3 wire, insulated/bonded neutral, 30 (1") spaces, 40 poles, 120/240 volt AC. Main breaker type BW at 25,000 AIC. Furnished with hub closure plates, hubs and ground bar kit (necessary for sub-feeding) sold separately. Tin plated aluminum bus bar. Twin neutral with non-removable cross bus connecting them. When bonded, unused neutral connections may be used for equipment ground protectors in service entrance application. #2 - 300 kcmil wire range. Electrostatic powder coat, baked urethane painted. Rotate 180 degrees for bottom feed; orientation of main breaker handle consistent with NEC 240-81 requirements because it operates horizontally. 14-5/16" x 34-1/8" x 5-3/16". UL Listed file E52977.

A loadcenter is called a breaker box, electrical box or even a fuse box. The main function is to take electricity supplied by the utility and distribute it throughout the home to feed lights and receptacles. Not only does the loadcenter distribute power, it also provides protection.

Load Centers are enclosures specifically designed to house the branch circuit breakers and wiring required to distribute power to individual circuits. They contain either a main breaker when used at the service entrance point or a main lug when used as a sub-panel to add circuits to existing service. The main breaker protects the main entire panel and can be used as a service disconnect. The branch breakers protect the wires leading to individual electrical loads such as fixtures and outlets.

Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts one #14 - #4 copper wire or one #12 - #4 aluminum wire, two #14 - #12 copper wire or two #12 - #10 aluminum wire. ANSI certified and UL listed.

Fit many types of service entrance devices and load center covers. Use them to replace lost or damaged screws.

Air conditioning disconnects from Schneider Electric are Underwriters Laboratories? (UL?) Listed NEMA Type 3R rainproof. They are designed to meet all current National Electrical Code? (NEC?) requirements for a disconnecting means on residential and commercial air conditioning installations, as well as other single-phase applications, such as swimming pools and pump houses.

An air conditioning disconnect (ACD) is a disconnect located between the load center and the air conditioner. Eaton's ACD provides an installer or repair personnel with a visible disconnecting means when performing maintenance.

Eaton Load Center, 120/240 VAC, 200 A, Number of Phases: 1, Number of Spaces: 30, Number of Poles: 1, Number of Circuits: 60, Breaker/Load Center Type: Main Breaker, Plug-On Neutral, Type BR, Interrupt Rating: 22 kAIC, Cable Size: #6 to 2/0 AWG, Bus Bar Material: Aluminum, Enclosure Type: NEMA 1

An air conditioning disconnect (ACD) is a disconnect located between the load center and the air conditioner. Eaton's ACD provides an installer or repair personnel with a visible disconnecting means when performing maintenance.

Cutler-Hammer Main Lug Kit, 120/240 VAC, 200 A, 1 to 300 kcmil Wire

Sub feed lug kit. 125 A. 2-pole. Lugs to sub feed to another panel.

Used for sealing off a hub opening when a service feed originates underground. The plate is compatible with A-type openings and can be used on outdoor devices that utilize a 4-hole mounting pattern. Use for A-size hub opening for Square D metering equipment. UL and CSA listed.

Galvanized steel enclosure. Single phase, 3-wire, four jaw, 600 V maximum. Jaws fabricated from high conductivity, tin-plated, copper alloy. Insulating jaw support blocks of high impact, non-tracking thermoset polyester. Safety guides reduce chances of accidental contact and aligns meter in sock. Uses RX style hub (not included). Includes two ground lugs. Swing switches are stainless steel. Provision for 5th jaw. UL listed.

These indoor surface mount transfer switches are designed for fast installation in residential and commercial applications. The 18 in flexible conduit whip attaches easily to the load center and all wires are clearly marked. Simply select the circuits needed in an emergency and connect them to the Pro/Tran wire leads.

Speedfax Load Center, 120/240 VAC, 200 A, 1 Phases, 3-Wire Wiring, 22 kA Interrupt, MBK200 Main Breaker Circuit Breaker, Plug-In, 4 Spaces, 8 Circuits, Ring Cover, Tin Plated Copper Buss Bar, Surface Mounting, Nema 3R Enclosure, 30 in Overall Height, 14 in Overall Width, 5 in Overall Depth, CSA Certified, UL Listed, 1 in Spacing

The Easy/Tran TF transfer switch is designed for the control of a single circuit, such as a forced-air furnace, in the event of a power failure. The attached 18 in flexible aluminum conduit is pre-wired and allows the TF to be easily connected at the circuit breaker panel or the furnace or at any point in between. Power can be supplied from a portable generator, inverter, RV generator, fuel cell or any standby source capable of producing sufficient current to operate the desired load. Uses standard grounded extension cord.

These indoor surface mount transfer switches are designed for fast installation in residential and commercial applications. The 18 in flexible conduit whip attaches easily to the load center and all wires are clearly marked. Simply select the circuits needed in an emergency and connect them to the Pro/Tran wire leads.

Connecticut Electric RV/EV power outlet. Features heavy-duty steel construction with powder coat finish in a 3R rainproof enclosure. Outlet NEMA 14-50 receptacle.

Single phase, 3-wire, 4-jaw, 600 V maximum. Jaws fabricated from high conductivity, tin-plated, copper alloy. Insulating jaw support blocks of high impact, non-tracking thermoset polyester. Galvanized steel enclosure. Safety guides reduce chances of accidental contact and aligns meter in sock. Uses RX style hub (not included). Provision for 5th jaw and closure plate included, no bypass. UL listed.

Code-gauge steel enclosure. Single phase, 3-wire, solid neutral, 4 space/8 circuits 1-pole, 2 QP breakers 2-pole, 120/240 VAC. 10,000 AIR. With closure plates, HS-hubs sold separately. One piece plated aluminum bus bar. 100% circuit breaker twist outs. Positive load side circuit breaker hook rail. Suitable for use as service equipment when a main breaker (100 A maximum) is back-fed in a branch position and used with main breaker retainer clip No MBR1. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 deg for bottom feed. Gray enamel finish. CSA and UL listed, complies fully with NEC and UL requirements for Class CTL. 6 in x 12-1/4 in x 4-1/4 in.

Single phase, 2 spaces/4 circuits, 120/240 V. 10,000 AIR. Factory installed main breaker. Additional spaces allow connection of external circuits such as yard lights. One 1-1/4 in HS125 hub included. Normally used as a means of disconnecting power to a mobile home panel, but also used as a disconnect for houses. Aluminum bus bar insulates and secures interior. Gray enamel finish. Pole mountable. UL listed for use as service entrance equipment.

Code-gauge steel enclosure. Single phase, 3-wire, solid neutral, 8 spaces and 16 circuits maximum 1-pole, 4 QP breakers maximum 2-pole, 120/240 V. 10,000 AIR. One piece plated aluminum bus bar. 100% circuit breaker twist outs. Positive load side circuit breaker hook rail. Suitable for use as service entrance equipment when a main breaker (125 A maximum) is back-fed in branch position and used with main breaker retainer clip No MBR1. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 deg for bottom feed. Gray enamel finish. 12-3/8 in x 14-3/4 in x 3-7/8 in. UL listed, complies fully with NEC and UL requirements for Class CTL.

Code-gauge steel enclosure. Single phase, 3-wire, solid neutral, 8 space/16 circuits 1-pole, 4 QP breakers 2-pole, 120/240 VAC. 10,000 AIR. HS-hubs sold separately. One piece copper bus bar, 100% circuit breaker twist outs. Positive load side circuit breaker hook rail. Suitable for use as service equipment when a main breaker (125 A maximum) is back-fed in a branch position and used with main breaker retainer clip No MBR1. When used as service equipment, any unused neutral position may be used for equipment grounding. Rotate entire device 180 deg for bottom feed. Gray enamel finish. UL listed, complies fully with NEC and UL requirements for Class CTL. 12-1/8 in x 14-3/4 in x 4-1/4 in.

Single-phase, 3-wire, 4-jaw, 600 V maximum. Jaws fabricated from high conductivity, tin-plated, copper alloy. Insulating jaw support blocks of high impact, non-tracking thermoset polyester. Galvanized steel enclosure. Safety guides reduce chances of accidental contact and aligns meter in sock. Uses RX style hub (not included). Provision for 5th jaw, no bypass. UL listed.

Plastic (snap-in) for type BR 1 in space. May also be used with 400 and 600 A load centers.

Load Centers are enclosures specifically designed to house the branch circuit breakers and wiring required to distribute power to individual circuits. They contain either a main breaker when used at the service entrance point or a main lug when used as a sub-panel to add circuits to existing service. The main breaker protects the main entire panel and can be used as a service disconnect. The branch breakers protect the wires leading to individual electrical loads such as fixtures and outlets.

Load Centers are enclosures specifically designed to house the branch circuit breakers and wiring required to distribute power to individual circuits. They contain either a main breaker when used at the service entrance point or a main lug when used as a sub-panel to add circuits to existing service. The main breaker protects the main entire panel and can be used as a service disconnect. The branch breakers protect the wires leading to individual electrical loads such as fixtures and outlets.

Outdoor main lug load center, 100 A, 6 space and 12 circuits. Can be wired for underground or overhead feeds with a 2-1/2 in hub on the top and a 1-1/2 in knockout on the bottom. NEMA type 3R enclosure resists rain for durable performance. ANSI certified and UL listed.

Main lug indoor load center, 70 A, 2 space/4 circuits. Maximum SCCR of 10,000 and a maximum load of 240 V. NEMA type 1 enclosure. Expandable load center capacity with the use of tandem or quad breakers. CSA approved for vertical, horizontal or inverted mounting. Accepts aluminum or copper conductors. Approved to only accept Canadian Homeline breakers.

Main lug indoor load center, 100 A, 6 space/12 circuit. NEMA type 1 enclosure. Single phase, 3-wire, solid neutral. Expandable load center capacity with the use of tandem or quad breakers. CSA approved for vertical, horizontal or inverted mounting. Accepts aluminum or copper conductors. Approved to only accept Canadian Homeline breakers.

Single phase, 3-wire, 4-jaw, 600 VAC maximum. 10,000 RMS symmetrical amp short circuit current rating. Hub provisions have an A-type size and its enclosure is made of aluminum. Supplied with bonded neutral. Requires bolt-on hub or closing plate (not included) for hub opening in top endwall. Bypass and jaw release sold separately. It can accommodate buildings supplied by overhead power lines or underground cables. UL listed.

Single phase, 2-pole, 3 wire (2 blades, fuseholders and 1 neutral), 120/240 VAC. Rated 3 hp at 240 VAC, with metallic enclosure. 10,000 AIC (short circuit rating) with class H cartridge fuses. NEMA type 1 enclosure. Terminal lug data: (1) #12 - 6 Al or #14 - 6 Cu. wire. Service ground bar kit PKGTA1 sold separately. Padlock attachment for lock off. UL listed, meets NEMA standard KS1.

Main lug indoor load center, 100 A, 6 space/12 circuit, intended for use in fixed applications. NEMA type 1 enclosure and a copper bus bar for conductivity. Single-phase, rated for up to 240 V and has a 10,000 maximum SCCR. UL listed.

Single phase, 2 pole, 2 wire, 240 VAC. Rated 3 hp at 120 V, 10 hp at 240 V. For top and bottom entry and exit, with provision for type H conduit hub. Heavy-duty, high strength, rugged polymer enclosure with UV-resistant features. Swing-up cover remains in place when in open position, protective shield can be removed for access to fuses. No GB4 ground bar and No 360-011-24 pullout head replacement sold separately. #14-2 AWG wire range. 5 in x 8-5/8 in x 3-1/2 in. UL listed file No E5239.

Steel enclosure. 2-pole, 3-wire, 2 blades, 2 class H cartridge fuses (not included), solid neutral, 120/240 VAC. Rated 1-1/2 to 3 hp single phase, 3 to 7-1/2 hp 3-phase at 240 V only when dual element fuses are used. For residential and commercial applications. Suitable for light duty motor circuits and service entrance. For use on systems capable of delivering up to 10,000 rms, symmetrical fault current. Bolt on hub provided. DS100GK ground kit sold separately. 6-1/6 in x 7-1/2 in x 6-3/4 in. UL listed file No.E5239; meets UL98 for enclosed switches and NEMA standard KS1.

PowerMark Gold load centers lower your costs by making installation faster and easier, increasing application flexibility and reducing inventory requirements. At the same time, they deliver obvious and significant advances in design, function and quality.

Designed for residential or light commercial applications where duty is not severe. Meets or exceeds NEMA Enclosed Switch Standard KS1-1983 for type GD, CSA certified; 60 deg C/75 deg C conductor rating. Two pole, 120/240 VAC; 250 VDC. Removable closing cap. Accepts Class H fuses (not included). Feature quick make, quick break mechanism. Suitable for use as service entrance equipment when installed in accordance with National Electrical Code. 6-7/8 in x 9-7/8 in x 3-5/16 in. UL listed (Enclosed Switches No. 98).

PowerMark Gold load centers lower your costs by making installation faster and easier, increasing application flexibility and reducing inventory requirements. At the same time, they deliver obvious and significant advances in design, function and quality.

The raintight NEMA 3R power inlet box is designed for the use with the Pro/Tran transfer switches and Reliance? panel or link manual transfer panels and generator-ready load centers. The power inlet box may be installed indoors or outdoors in an open area where the generator is being used. Using one of the four combination 1/2 in and 3/4 in knockouts (one on each side, bottom and back) the power inlet box can be wired directly to the transfer switch or panel. The exclusive patented design provides generous wiring space and facilitates rough-in. The PR Series includes circuit breakers that match the amperage of the power inlet. UL listed. The raintight NEMA 3R PBN Series non-metallic power inlet box is designed for use with the Pro/Tran transfer switches and panel or link manual transfer panels and generator-ready load centers. This power inlet box must be installed outdoors in an open area where the generator is being used. Using one of the three 3/4 in knockouts (one each on the sides and back) the power inlet box can be wired directly to the transfer switch or panel. The patented design provides over 100 cu-in of wiring space and the slide-out base allows easy 360 deg access to the flanged inlet.

Connecticut Electric RV/EV power outlet. Features heavy-duty steel construction with powder coat finish in a 3R rainproof enclosure. Outlet TT-30 travel trailer receptacle.

The raintight NEMA 3R power inlet box is designed for the use with the Pro/Tran transfer switches and Reliance? panel or link manual transfer panels and generator-ready load centers. The power inlet box may be installed indoors or outdoors in an open area where the generator is being used. Using one of the four combination 1/2 in and 3/4 in knockouts (one on each side, bottom and back) the power inlet box can be wired directly to the transfer switch or panel. The exclusive patented design provides generous wiring space and facilitates rough-in. The PR Series includes circuit breakers that match the amperage of the power inlet. UL listed. The raintight NEMA 3R PBN Series non-metallic power inlet box is designed for use with the Pro/Tran transfer switches and panel or link manual transfer panels and generator-ready load centers. This power inlet box must be installed outdoors in an open area where the generator is being used. Using one of the three 3/4 in knockouts (one each on the sides and back) the power inlet box can be wired directly to the transfer switch or panel. The patented design provides over 100 cu-in of wiring space and the slide-out base allows easy 360 deg access to the flanged inlet.

Speedfax Load Center, 120/240 VAC, 200 A, 1 Phases, 3-Wire Wiring, 22 kA Interrupt, MBK200 Main Breaker Circuit Breaker, 4 Spaces, 8 Circuits, Ringless Cover, Tin Plated Copper Buss Bar, Surface Mounting, Nema 3R Enclosure, 30 in Overall Height, 14 in Overall Width, 5 in Overall Depth, UL Listed, 1 in Spacing