Includes distributor tubes, distributor head, water distributor adapter, MEK solvent and instructions.

Dial Pillow Block Bearing, Dimensions: 5/8 in Dia, Suitable for: Evaporative Cooler Purge Systems

A time release formula that controls unpleasant odors from algae and bacteria in evaporative coolers and neutralizes odor in cooler water to freshen the air. Not for potable (drinkable) water.

For ductless installations and mobile homes. Diffuses air 4 ways or 6 ways with 14 adjustable louvers, made with white colored, high-impact plastic. Will not rust, corrode or stain. For duct openings up to 20 in x 20 in. Grille is 22-1/2 in x 22-1/2 in x 3-1/8 in depth. Easy to install. For all residential cooler models.

Dial Manufacturing Evaporative Cooler Pad, Aspen Fiber, Dimensions: 28 x 32 in, Package Type: Bundle, Package Quantity: 24

Use to run water to cooler. Attaches to copper pipe 3/8 to 1-3/8 in OD. Available with rigid self piercing needle.

The open cellular structure of this excelsior allows premier pad to hold more water, this results in more evaporative wicking area per square inch than any other evaporative cooler pad. Delivered up to 7 deg cooler air than paper or synthetic pads.

1/4 in CC Tee, for connecting two coolers to one water source. Includes poly tube adapters.

Variable pulleys must be opened 2-1/2 to 5 full turns, depending on air resistance or motor will overheat. If motor cycles (stops and starts due to over-heating), open variable pulley until motor stops cycling. If cycling persists when pulley is fully opened, you must use the next size smaller pulley. Always use pulley size recommended by cooler manufacturer.

Provides a one step treatment to inhibit build-up of scale, rust and offensive odor. Conditions cooler pad to reduce air temperature. Contains mild acid and wetting agents, not for potable water.

Dial Pillow Block Bearing, Dimensions: 1 in Dia, Suitable for: Evaporative Cooler Purge Systems

Includes distributor tubes, distributor head, water distributor adapter, MEK solvent and instructions.

1/2 in MPT overflow pipe with flat sided hex head for easy install and removal. Washer included. Nylon drain with 1/2 in FTP ID and 3/4 in male garden hose threads OD.

The open cellular structure of this excelsior allows premier pad to hold more water, this results in more evaporative wicking area per square inch than any other evaporative cooler pad. Delivered up to 7 deg cooler air than paper or synthetic pads.

Standard for residential and commercial pumps with 4500 to 11,000 cfm ratings. Use to run water from pump to distributor.

High efficiency, high-temperature insulation system. Capable of withstanding temperatures over 300 deg F. Reduces motor failures due to heat aging. Premium moisture-resistant insulation system. Styrenated epoxy coating on rotor prevents rust build-up and extends the life of the motor. 115 V, all copper windings, no base, 56Z frame. Auto-reset thermal overload protection. Great starting switch features. Heavy-duty bronze bearing. Mechanically and electrically approved for evaporative cooler applications. Label and instructions in English and Spanish. UL approved construction.

Kit fits 3-way side, 4-way down, 6-way side and 8-way down by using an 8 way down distributor with up to 5 inserts plugs and MEK. Includes distributor head, water distributor adapter, MEK solvent and instructions.

Molded 3 prong plug and extra-long grounded cord fits Champion cooler mounting bracket. Built-in supplementary pump screen, flame-retardant motor housing and auto-reset thermal overload protection. Corrosion-resistant shaft. Permalube bearings. Built-in barbed elbow. Removable base plate for ease of cleaning. Operates in water reservoirs of 1/2 to 4 in 120 VAC, 60 Hz, UL classified.

Fits all offset and concentric pumps.

Dial Spider Bearing, Dimensions: 1 in Dia, Suitable for: Evaporative Cooler Purge Systems

For cooler bearings and some cooler motors with oilable bearings. Lubricate shaft bearings at the start of every season and every 60 days during season. Inhibits rust and oxidation.

Dura-Cool, foamed polyester pad. Non-allergenic, odorless, cooler air and won't shed fiber. Color blue.

Provides a one step treatment to inhibit build-up of scale, rust and offensive odor. Conditions cooler pad to reduce air temperature. Contains mild acid and wetting agents, not for potable water.

The open cellular structure of this excelsior allows premier pad to hold more water, this results in more evaporative wicking area per square inch than any other evaporative cooler pad. Delivered up to 7 deg cooler air than paper or synthetic pads.

High efficiency, high-temperature insulation system. Capable of withstanding temperatures over 300 deg F. Reduces motor failures due to heat aging. Premium moisture-resistant insulation system. Styrenated epoxy coating on rotor prevents rust build-up and extends the life of the motor. 115 V, all copper windings, no base, 56Z frame. Auto-reset thermal overload protection. Great starting switch features. Heavy-duty bronze bearing. Mechanically and electrically approved for evaporative cooler applications. Label and instructions in English and Spanish. UL approved construction.

For Arctic Circle, Arvin and McGraw coolers.

1/4 in CC x 1/8 in MPT. Use with copper or poly tube on side tapped sill cock or pipe adapter. Includes poly tube adapter.

Brass inlet, arm and stem. Polypropylene body and float. Noiseless and non-corrosive.

Molded 3 prong plug and extra-long grounded cord fits Champion cooler mounting bracket. Built-in supplementary pump screen, flame-retardant motor housing and auto-reset thermal overload protection. Corrosion-resistant shaft. Permalube bearings. Built-in barbed elbow. Removable base plate for ease of cleaning. Operates in water reservoirs of 1/2 to 4 in. 120 VAC, 60 Hz, UL classified.

Adapts poly tube to brass fittings without using 1/4 in CC sleeve.

Has heavy-duty bearings, pumps more water, is more efficient than the offset design and has longer life/warranty period.

The open cellular structure of this excelsior allows premier pad to hold more water, this results in more evaporative wicking area per square inch than any other evaporative cooler pad. Delivered up to 7 deg cooler air than paper or synthetic pads.

Resistant to UV degradation, use to run water to coolers, not for potable water. Do not use indoors or in attic.

For Arctic Circle, Arvin and McGraw coolers.

Includes distributor tubes, distributor head, water distributor adapter, MEK solvent and instructions.

20-1/8 in end to bend length. Fits all residential coolers.

Designed for use with 1/3, 1/2,3/4 and 1 hp, 1-speed and 2-speed, 115 V and 230 V cooler motors. Mounts in either a standard single 2x4 or double 4x4 gang electrical box. Unit automatically resets to 77 deg in the event of a power failure.

Premium, heavy-bodied, "one coat" coating. Apply with a brush. Designed to coat and seal evaporative cooler bottom pans, protect against rust and corrosion all season, help deaden sound. Resistant to moisture, non-asbestos and fast drying.

High efficiency, high-temperature insulation system. Capable of withstanding temperatures over 300 deg F. Reduces motor failures due to heat aging. Premium moisture-resistant insulation system. Styrenated epoxy coating on rotor prevents rust build-up and extends the life of the motor. 115 V, all copper windings, no base, 56Z frame. Auto-reset thermal overload protection. Great starting switch features. Heavy-duty bronze bearing. Mechanically and electrically approved for evaporative cooler applications. Label and instructions in English and Spanish. UL approved construction.

Dial MAXCOOL Aspen Pad, Dimensions 29 x 29 in, Bundle, 24

Union for 1/4 in OD copper tubes.

Includes distributor tubes, distributor head, water distributor adapter, MEK solvent and instructions.

Run water to coolers & humidifiers. Not recommended for refrigeration lines. Do not use for potable (Drinkable) water applications.

Heavy-duty corrosion resistant brass body, brass plunger, arm and stem. Polypropylene float. 2-piece arm with adjustable screw.

1/4 in CC x 1/8 MPT Angle water shut off valve. Includes poly tube adapter, fits sill cocks and pipe adapter.

A time release formula that controls unpleasant odors from algae and bacteria in evaporative coolers and neutralizes odor in cooler water to freshen the air, not for potable (drinkable) water.

Premium, heavy-bodied, "one coat" coating. Apply with a brush. Designed to coat and seal evaporative cooler bottom pans, protect against rust and corrosion all season, help deaden sound. Resistant to moisture, non-asbestos and fast drying.

Everything needed to run water to an evaporative cooler. Includes: 1/4 in x 25 ft poly tube, brass sill cock with garden hose thread x 1/8 FPT tapped on side, hose washer, 1/4 cc x 1/8 MPT male union, (2) 1/4 in poly tube adapters and installation instructions. For outdoor use only.

Cellulose base impregnated with plastic resins and anti-rot agents. 50% heavier than paper, holds more water and lasts longer, with high air velocity and fast wet-out. Energy efficient, durable and easy to install.

The open cellular structure of this excelsior allows premier pad to hold more water, this results in more evaporative wicking area per square inch than any other evaporative cooler pad. Delivered up to 7 deg cooler air than paper or synthetic pads.

The open cellular structure of this excelsior allows premier pad to hold more water, this results in more evaporative wicking area per square inch than any other evaporative cooler pad. Delivered up to 7 deg cooler air than paper or synthetic pads.

Cellulose base impregnated with plastic resins and anti-rot agents. 50% heavier than paper, holds more water and lasts longer, with high air velocity and fast wet-out. Energy efficient, durable and easy to install.

Has heavy-duty bearings, pumps more water, is more efficient than the offset design and has longer life/warranty period.

Prevents sagging and movement. Replacement for Artic Circle, Arvin and McGraw.

Dial Pillow Block Bearing, Dimensions: 3/4 in Dia, Suitable for: Evaporative Cooler Purge Systems

More efficient than paper, non-allergenic, odorless, will not shed fiber.

Standard compression sleeve and nut for 1/4 in O.D copper tube. Two nuts and two sleeves.

Controls scale build-up and corrosion in coolers. Special formula holds minerals in suspension by raising the solubility level of the water. Reduces mineral build-up on pads must be used with a bleed off kit or PowerClean? purge pump to flush suspended minerals.

High efficiency, high-temperature insulation system. Capable of withstanding temperatures over 300 deg F. Reduces motor failures due to heat aging. Premium moisture-resistant insulation system. Styrenated epoxy coating on rotor prevents rust build-up and extends the life of the motor. 115 V, all copper windings, no base, 56Z frame. Auto-reset thermal overload protection. Great starting switch features. Heavy-duty bronze bearing. Mechanically and electrically approved for evaporative cooler applications. Label and instructions in English and Spanish. UL approved construction.

Dial MAXCOOL Aspen Pad, Dimensions 28 x 34 in, Bundle, 24

Dial Manufacturing Evaporative Cooler Pad, Aspen Fiber, Dimensions: 24 x 26 in, Package Type: Bundle, Package Quantity: 24

Cooler touch up spray paint. Exterior, aerosol spray can. Tan/almond color.

Works as a sacrificial metal to protect cooler cabinet and parts. Unique anode tray design keeps anode above metal cooler bottom and allows anode to degrade evenly on all sides.

Fast drying spray coating. Designed to coat and seal evaporative cooler interior, protect against rust and corrosion all season.

Variable pulleys must be opened 2-1/2 to 5 in full turns, depending on air resistance or motor will overheat. If motor cycles, open variable pulley until motor stops cycling. If cycling persists when pulley is fully opened, you must use the next size smaller pulley. Always use pulley size recommended by cooler manufacturer.

Dial Spider Bearing, Dimensions: 3/4 in Dia, Suitable for: Evaporative Cooler Purge Systems

Heavy duty bronze body, brass plunger, arm and stem, polypropylene float, 2-piece arm with adjustable screw and heavy duty threads tapped for 1/4 in female pipe. For industrial coolers.

Run water to coolers & humidifiers. Not recommended for refrigeration lines. Do not use for potable (Drinkable) water applications.

Cellulose base impregnated with plastic resins and anti-rot agents. 50% heavier than paper, holds more water and lasts longer, with high air velocity and fast wet-out. Energy efficient, durable and easy to install.

Formed basket, fits all pumps. 8 in L x 6 in W x 3-1/2 in H.

Molded motor plug cords with 115 V configuration will fit all 115 V motor receptacle cords & pigtails. 230 V molded motor plug cords have 230 V prong configuration.

Sill cock garden hose thread fits directly onto existing outdoor faucet. Attach angle needle valve or male compression coupling to side tapped 1/8 in FIP to connect to cooler.

Controls scale build-up and corrosion in coolers, special formula holds minerals in suspension by raising the solubility level of the water. Reduces mineral build-up on pads must be used with a bleed off kit or PowerClean? purge pump to flush suspended minerals.

Has heavy-duty bearings, pumps more water, is more efficient than the offset design and has longer life/warranty period.

Molded 3 prong plug and extra-long grounded cord fits Champion cooler mounting bracket. Built-in supplementary pump screen, flame-retardant motor housing and auto-reset thermal overload protection. Corrosion-resistant shaft. Permalube bearings. Built-in barbed elbow. Removable base plate for ease of cleaning. Operates in water reservoirs of 1/2 to 4 in, 120 VAC, 60 Hz, UL classified.

Includes slip in, non-threaded overflow pipe, washer, poly drain with 3/4 in male garden hose threads.

1/4 in CC x 1/8 MPT straight water shut-off valve. Includes poly tube adapter.

High efficiency, high-temperature insulation system. Capable of withstanding temperatures over 300 deg F. Reduces motor failures due to heat aging. Premium moisture-resistant insulation system. Styrenated epoxy coating on rotor prevents rust build-up and extends the life of the motor. 115 V, all copper windings, no base, 56Z frame. Auto-reset thermal overload protection. Great starting switch features. Heavy-duty bronze bearing. Mechanically and electrically approved for evaporative cooler applications. Label and instructions in English and Spanish. UL approved construction.

Prevents sagging and movement. Replacement for Champion Coolers.

Dial MAXCOOL Aspen Pad, Dimensions: 32 x 40 in

300 denier x 300 denier polyester fabric with double stitched seams, strong draw rope and heavy-duty brass grommets. Compared to canvas, these covers are stronger, last longer and won't shrink. The water-resistant polyurethane coating prevents water from entering cooler while still allowing water vapor to escape, inhibiting moisture buildup inside cooler. Cover is suitable to all seasons as it protects cooler from rain, snow and UV.

Threaded nylon overflow pipe has 1/2 in MPT standpipe with hex head top, 1/2 in thread length, 3 in smooth length. Black color.

Standard compression sleeve for 1/4 in OD copper tube.

The open cellular structure of this excelsior allows premier pad to hold more water, this results in more evaporative wicking area per square inch than any other evaporative cooler pad. Delivered up to 7 deg cooler air than paper or synthetic pads.

The automatic Power-Clean? mineral and scale elimination system will save money and conserve water by automatically flushing your cooler clean every 8 hr of existing cooler pump operation. The new test button feature on the Power-Clean? system will activate the 7 min purge cycle. Once this cycle is complete, the 8 hr purge timer will reset. Power-Clean? connects directly to the existing cooler pump (recirculating pump). Once installed in the pan of the cooler, Power-Clean? automatically cycles every 8 hr of cooler pump operation to empty the water and replenish the cooler with fresh water. The cooler capability is never interrupted. Replacing the cooler water on a regular basis is beneficial by removing mineral scale build-up and bacterial growth. Power-Clean? eliminates the need for a bleed-off and the use of cleaners or harsh chemical additives.

Connects pump hose to water distributor head.

Dial MAXCOOL Aspen Pad, Dimensions 24 x 36 in, Bundle, 24

Resistant to UV degradation, use to run water to coolers, not for potable water. Do not use indoors or in attic.

Everything needed to install a pump on a new or existing evaporative cooler. Contains: 1/4 in float valve, water distributor adapter, 1/2 in 5 ft vinyl pump hose, pump hose restrictor, round formed basket, 2 hose ring clamps, plastic drain and overflow pipe and installation instructions.

Brass body casting, arm and stem. Stainless steel seat, polypropylene float. Plunger rotates to discourage alkali deposits.

Variable pulleys must be opened 2-1/2 to 5 full turns, depending on air resistance or motor will overheat. If motor cycles, open variable pulley until motor stops cycling. If cycling persists when pulley is fully opened, you must use the next size smaller pulley. Always use pulley size recommended by cooler manufacturer.

High efficiency, high-temperature insulation system. Capable of withstanding temperatures over 300 deg F. Reduces motor failures due to heat aging. Premium moisture-resistant insulation system. Styrenated epoxy coating on rotor prevents rust build-up and extends the life of the motor. 115 V, all copper windings, no base, 56Z frame. Auto-reset thermal overload protection. Great starting switch features. Heavy-duty bronze bearing. Mechanically and electrically approved for evaporative cooler applications. Label and instructions in English and Spanish. UL approved construction.

Dial Manufacturing Evaporative Cooler Pad, Aspen Fiber, Dimensions: 20 x 36 in, Package Type: Bundle, Package Quantity: 24, Suitable for: Tradewinds TC-451 Coolers

1/4 in CC x 1/4 in CC straight in line water shut-off valve. Includes poly tube adapters for 1/4 in poly tube.

Set of 2 for standard 2-1/2 in resilient motor mounting rings.

6 position rotary wall switch for two-speed evaporative coolers. Kits include plastic plate, mounting screws and wiring diagram. UL recognized component rotary switch. Rated for 1/3 to 3/4 hp motors.

Anderson Metals Cooler Nipple, Brass, Suitable for: Evaporative Cooler Purge Systems

3/4 in female hose connection inlet x 3/4 in hose connection with tapped 1/8 in I.P, straight through side wall.

3/4 in FIP inlet x 3/4 in hose connection with tapped 1/8 in I.P, straight through side wall.

B & K Evaporative Cooler Valve, Specifications: 3/4 in FHT Inlet, Brass